NEW 65-74 CHEVY LONG TUBE HEADERS,CERAMIC COATED,BBC,V-8,IMPALA,BEL AIR,CAMARO

Description: You are bidding on a Pair of Brand New Southwest Speed Ceramic Hot Coated Long Tube Headers that fits 1965-1974 Chevy Passenger Cars with Big Block Chevy 396-454ci Engines (SWS Part #440-2400). These Southwest Speed long tube headers are a direct fit for 1965-1974 Chevy passenger cars with Big Block Chevy V-8 engines, and will work with both automatic & manual transmissions. These headers are a chassis header and are meant to go inside of the frame rails on 1965-1974 Chevrolet Chassis. The collectors exit toward the rear of the engine compartment and are well above the under carriage of the vehicle, eliminating the chance of the collectors contacting the ground. The unique design of the collector location makes these headers a great choice for many GM passenger cars that include: 1965-1970 Bel Air, Biscayne, & Impala, 1967-1969 Camaro, and 1968-1974 Nova with Big Block Chevy Engines. Original Big Block frame stands and motor mounts must be used to insure proper engine location and header fit. Ground parallel with .380" flanges on the cylinder head surface with 2" primary tubes, & feature 3-1/2" collectors and are supplied with 2-1/2" reducers that bolt to the collectors, to connect the rest of the exhaust system to the vehicle. Sold complete with header bolts and gaskets, and reducer bolts and gaskets. These Headers will fit angle plug or straight plug heads, and no spark plug or spark plug wire restrictions. Ceramic Hot Coating (CHC) is a heat resistant, ceramic coating applied to the outside of the header. This coating will reflect heat, which helps retain more heat within the header tube, while simultaneously speeding up the exhaust flow. Not only will this coating help you make more horsepower, it also keeps your headers rust-free, looking great, and lasting longer (when properly maintained). If you are looking for a quality finish for your headers, this is it. Good to 1300 degrees. Note: These headers will not fit 348ci & 409ci W-Series Big Block Chevy Engines Features: Will work with both automatic & manual transmissions in 1965-1974 Chevrolet Chassis 2" primaries to the 3 1/2" Collectors Includes a pair of 2-1/2" reducers to connect exhaust under the vehicle Great for some Hot Rods, Rat Rods & Street Rods More Performance Better Fuel Mileage Great Choice to replace cast iron exhaust manifolds Enhances the looks of any rod Includes gaskets and mounting hardware Ceramic Hot Coated to resist early corrosion Factory Applications: Chevy Passenger Cars with Big Block Engines: 1965-1970 Bel Air 1965-1970 Biscayne 1965-1970 Impala 1967-1969 Camaro 1968-1974 Nova Header Specs: Material Type: Steel Header Tube Type: Long Tube Flange Style: Round Port Flange Thickness: .380" Finish: Ceramic Hot Coated Hardware Included: Yes Gaskets Included: Yes Tube Outside Diameter: 2" Collector Diameter: 3 1/2" Reducer: 2 1/2" Reducer Length: 4 7/8" Notes: 1. Does Not Fit 348ci & 409ci W-Series Big Block Chevy Engines 2. Fits all Big Block Chevrolet V-8 engines with standard exhaust pattern 3. Fits 396, 402, 409, 427, & 454 Cu. In. Big Block Chevy Engines 4. Original Big Block frame stands and motor mounts must be used to insure proper engine location and header fit Ceramic Hot Coating Warning: Warning: CHC coatings will burn and be damaged at exhaust temperatures over 1300 degrees. A lean fuel mixture can generate exhaust temperatures exceeding 1700-1900 degrees. If the coating is damaged due to a lean condition, the coating will not be warranted, but can be recoated for a fee. No warranty or returns on Ceramic Hot Coated exhaust items once they have been installed. Header Return Policy: Please refer to the header measurement chart below to make sure the header will fit your vehicle and application before ordering. In the event you order a header that will not fit your vehicle and application, you may return them for a refund, providing you don't damage the header. When you receive the header the finish will be protected and must remain unscratched for a refund. If you bend or dimple any of the tubes or scratch the finish, we will not be able to sell the header and will not be able to process a refund. Use care when trial fitting headers. Repack them well to prevent damage returning them to us. We won't process refunds for scratched, dimpled, dented, or bent headers. We also have these same headers available in: Painted Flat Black Triple Process Chrome Plated Polished Stainless Steel You can view and download the complete instructions for these headers here. We also have thousands of other High Performance Parts in our store. Shipping: There is no faster shipping on Ebay. If you pay for the item by 5:00 Eastern, Monday-Friday, we will ship it the same day. If it's after 5:00 EST, we will ship it the next business day. If you pay for the item on the weekend, we will ship it out Monday. Ebay now requires that sellers put a "handling time" on each item and "1 Business Day" is the shortest listed option. WE DON'T HAVE A HANDLING TIME. We ship same day in accordance with the paragraph above. No delays here. We want you to have the parts as bad as you do. Shipping cost will be $29.99 within the continental United States. If you buy 2 or more of our auctions, shipping will certainly be combined to save you money. We will be glad to ship internationally. Just send me a message for an international shipping quote. Accepted payment methods: We accept Paypal. If buyer doesn’t have a Paypal account, he or she can pay with Visa, Mastercard, or Discover through seller’s merchant account. After purchasing, pay instantly with your credit card through PayPal!

Price: 499.99 USD

Location: Fort Smith, Arkansas

End Time: 2024-10-04T23:49:58.000Z

Shipping Cost: 29.99 USD